KaiserRolls Posted July 10, 2019 Author Report Share Posted July 10, 2019 18 minutes ago, YoungCR said: The one time I actually make it into town... And PB1 is “too far away” to come hang out... unreal Rekpoint and YoungCR 1 1 Quote Link to comment Share on other sites More sharing options...
patsbimmer1 Posted July 10, 2019 Report Share Posted July 10, 2019 18 hours ago, YoungCR said: The one time I actually make it into town... You should hang out more when I invite you places... Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted July 12, 2019 Author Report Share Posted July 12, 2019 Bummerworld 3” arrived. TMS shorty headers get here Saturday rampelsauce, wasnt m3 and patsbimmer1 3 Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted July 14, 2019 Author Report Share Posted July 14, 2019 ECS at it again patsbimmer1 and Jdesign 1 1 Quote Link to comment Share on other sites More sharing options...
wasnt m3 Posted July 14, 2019 Report Share Posted July 14, 2019 2 hours ago, KaiserRolls said: ECS at it again They sent you one header?!? Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted July 14, 2019 Author Report Share Posted July 14, 2019 14 minutes ago, wasnt m3 said: They sent you one header?!? Yep, 3 cyl conversion - I hope it saved them money on shipping lol patsbimmer1 and Jdesign 1 1 Quote Link to comment Share on other sites More sharing options...
Jdesign Posted July 17, 2019 Report Share Posted July 17, 2019 Fill it with dildos and send it back. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted July 17, 2019 Author Report Share Posted July 17, 2019 1 minute ago, Jdesign said: Fill it with dildos and send it back. The other half is supposed to arrive today. Will update on if it’s the correct one lol Jdesign 1 Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted July 17, 2019 Author Report Share Posted July 17, 2019 ECS is the butt of a lot of jokes usually, but ordering through @patsbimmer1 is the way to do it. He had the second piece overnighted and I didn’t have to deal with any mouthbreathers. If you need to order through ECS, hit up Pat. Jdesign, Rekpoint and patsbimmer1 3 Quote Link to comment Share on other sites More sharing options...
Jdesign Posted July 17, 2019 Report Share Posted July 17, 2019 19 minutes ago, KaiserRolls said: ECS is the butt of a lot of jokes usually, but ordering through @patsbimmer1 is the way to do it. He had the second piece overnighted and I didn’t have to deal with any mouthbreathers. If you need to order through ECS, hit up Pat. No Dillys needed! Quote Link to comment Share on other sites More sharing options...
Rekpoint Posted July 18, 2019 Report Share Posted July 18, 2019 9 hours ago, KaiserRolls said: ECS is the butt of a lot of jokes usually, but ordering through @patsbimmer1 is the way to do it. He had the second piece overnighted and I didn’t have to deal with any mouthbreathers. If you need to order through ECS, hit up Pat. Pat IS a live saver. He is the only reason I order from ECS patsbimmer1 1 Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 20, 2019 Author Report Share Posted August 20, 2019 Went to the shop. Tapped some holes. Tossed headers on. Check the ICV hoses for cracks, found some. Front lift point is all fucked so I went home. I’ll check back in a month B C, Rekpoint, Jdesign and 1 other 2 1 1 Quote Link to comment Share on other sites More sharing options...
straight6pwr Posted August 21, 2019 Report Share Posted August 21, 2019 lookin good', shawty. KaiserRolls 1 Quote Link to comment Share on other sites More sharing options...
wasnt m3 Posted August 22, 2019 Report Share Posted August 22, 2019 How hard do you suppose those shorties would be to install in a car. Do the primaries block studs? Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 22, 2019 Author Report Share Posted August 22, 2019 1 hour ago, wasnt m3 said: How hard do you suppose those shorties would be to install in a car. Do the primaries block studs? I’ll get some better pics for you wasnt m3 1 Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 22, 2019 Author Report Share Posted August 22, 2019 Got sent the wrong TOB. Ruined some stuff on the trans. Slow progress Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 23, 2019 Author Report Share Posted August 23, 2019 Headers are on By far the easiest set of aftermarket headers I’ve ever installed on these motors. Room to get to every nut/stud from the top side Jdesign 1 Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 23, 2019 Author Report Share Posted August 23, 2019 Also needed to fix the lift point. The top most bolt hole for the lift bracket was all blown apart. I wanted to just re tap the remaining area, but I Was not able to get a tap through whatever material that threaded portion was. Could barely drill it out to the right size. Decided to buy a stud and just jb weld the cock sucker in because it only needs to work one more time anyways. Had to re tap that lower lifting bracket bolt hole as well because the threads were junk. Also got a rethreaded brown temp sensor so the dash temp gauge will work. Had to chase those threads as well. I’m getting very familiar with my tap set lately. Correct TOB and new reverse switch hopefully get here Saturday, so I can get the trans tossed on. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 23, 2019 Author Report Share Posted August 23, 2019 Oh and swapped out the pilot bearings for the larger one to accommodate the zf. In case anyone is curious about your shaft size I have included a pic of the difference side note: 20ftlbs always seems like next to nothing for the pressure plate bolts Quote Link to comment Share on other sites More sharing options...
straight6pwr Posted August 23, 2019 Report Share Posted August 23, 2019 good info on the headers and TOB forget the lift point, just throw the chains around the spider hose, they are super strong and never break. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 23, 2019 Author Report Share Posted August 23, 2019 3 minutes ago, straight6pwr said: good info on the headers and TOB forget the lift point, just throw the chains around the spider hose, they are super strong and never break. I’ll get a comparison shot of the regular zf tob vs the 323TOB. Should be a difference of 4or5mm. Which should make up for the difference of dualmass/non dualmass flywheel. I want the clutch to engage not directly off the floor lol at spider hose. Should just lift it from the ICV hoses. Those things never break either 👀 Jdesign 1 Quote Link to comment Share on other sites More sharing options...
jc43089 Posted August 26, 2019 Report Share Posted August 26, 2019 On 8/23/2019 at 10:35 AM, KaiserRolls said: I’ll get a comparison shot of the regular zf tob vs the 323TOB. Should be a difference of 4or5mm. Which should make up for the difference of dualmass/non dualmass flywheel. I want the clutch to engage not directly off the floor lol at spider hose. Should just lift it from the ICV hoses. Those things never break either 👀 As long as you have URO brand you should be fine. Quote Link to comment Share on other sites More sharing options...
Rekpoint Posted August 26, 2019 Report Share Posted August 26, 2019 2 hours ago, jc43089 said: As long as you have URO brand you should be fine. Mitch only buys URO brand. Must be why his cars are always taken apart 🤷🏼♂️ Quote Link to comment Share on other sites More sharing options...
B C Posted August 26, 2019 Report Share Posted August 26, 2019 57 minutes ago, Rekpoint said: Mitch only buys URO brand. Must be why his cars are always taken apart 🤷🏼♂️ Careful, you are treading dangerous waters with comments like those. I will unfriend you on facebook Rekpoint 1 Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted August 26, 2019 Author Report Share Posted August 26, 2019 1 hour ago, Rekpoint said: Mitch only buys URO brand. Must be why his cars are always taken apart 🤷🏼♂️ B C, Jdesign, Rekpoint and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.