HipMF Posted February 25, 2015 Author Report Share Posted February 25, 2015 That's cool. I'm from Menasha, so you're not that far from me. I might have to take you up on that some time. I wouldn't necessarily assume that the you need to keep the tube the same size as the port, but it's probably not a bad idea to do it that way. To do it right though, you have to look at the area of the opening, not the perimeter, as well as the length of the runner from the valve to the end of the tube. The engineering concept that you're looking for is called "Helmholtz resonance". The wikipedia entry does a good job explaining it. The mass of the air in the runner causes it to have inertia, and the atmosphere outside the tube essentially acts like a spring. Putting some mass on a spring gives you a resonator. Changing the diameter or length of the runner changes the mass of the air inside and tunes the resonator to a different frequency (rpm). Quote Link to comment Share on other sites More sharing options...
HipMF Posted February 25, 2015 Author Report Share Posted February 25, 2015 Hellaflush Brembo brakes They're off an Alfa Romeo GTV6 Milano (i think...). Doesn't seem like much, but that's 40% more lightness. Also took the bottom end in today. Will be doing some damage on my credit card soon. Quote Link to comment Share on other sites More sharing options...
Earl Posted February 25, 2015 Report Share Posted February 25, 2015 Do those have the same bolt pattern as stock? If so, badass! Quote Link to comment Share on other sites More sharing options...
YoungCR Posted February 25, 2015 Report Share Posted February 25, 2015 What isn't light weight on a Italian car Quote Link to comment Share on other sites More sharing options...
HipMF Posted February 25, 2015 Author Report Share Posted February 25, 2015 The bolt pattern is the same but they're a little wider. If i switch to vented rotors I think they'll bolt right up. Otherwise I may have change the spacer between the two halves. I'm confident that they can be made to work without too much work.I've heard that they're used as an upgrade for air-cooled 911s too, so I feel lucky to have picked them up for a reasonable price. Quote Link to comment Share on other sites More sharing options...
patsbimmer1 Posted February 28, 2015 Report Share Posted February 28, 2015 What isn't light weight on a Italian carThe driver... YoungCR, DrLeadFoot and B C 3 Quote Link to comment Share on other sites More sharing options...
B C Posted February 28, 2015 Report Share Posted February 28, 2015 Now I feel the urge to watch italian spiderman : Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 1, 2015 Author Report Share Posted March 1, 2015 I was trying to think of a clever comment for this one, but I got nothing. Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 1, 2015 Author Report Share Posted March 1, 2015 Jake farting at my new wheels. Quote Link to comment Share on other sites More sharing options...
YoungCR Posted March 1, 2015 Report Share Posted March 1, 2015 Full size Chevy ftw! I don't think I got a picture of it but the last E28 shell I scrapped was hauled on a uhaul 6x12 utility trailer with the tailgate down because it was 14 ft long. I also dragged the shell out of my garage on frame with the burb.Edit found the pic! Luckily with the snow I was able to rotate the shell by myself and then winch it on the trailer. Which leads me to the question on how you lifted the shell into the truck bed? Haha Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 1, 2015 Author Report Share Posted March 1, 2015 I was surprised, the empty shell of a car is actually pretty light. Three of us lifted the front up by hand, and then used the engine hoist to lift the back up and pushed it in. Sounds simple, but it was a bit of work. I think it took about an hour start to finish. Quote Link to comment Share on other sites More sharing options...
suspenceful Posted March 1, 2015 Report Share Posted March 1, 2015 I was trying to think of a clever comment for this one, but I got nothing. Jake farting at my new wheels. Quoting these two pictures to carry the epicness on to page 4... GunMetalGrey 1 Quote Link to comment Share on other sites More sharing options...
jc43089 Posted March 2, 2015 Report Share Posted March 2, 2015 Good to know about the uhaul trailer. That may be how I haul my e36 shell for moving. Sent from my potato phone Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted March 2, 2015 Report Share Posted March 2, 2015 Ha, putting that e30 into a truck bed was one of the funnier things that I have done with a car. E21 looks mint on those wheels. Quote Link to comment Share on other sites More sharing options...
ClassE Posted March 2, 2015 Report Share Posted March 2, 2015 Why is the shell being scrapped? Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted March 2, 2015 Report Share Posted March 2, 2015 That was Mike's car that met the guard rail Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 2, 2015 Author Report Share Posted March 2, 2015 Aside from the damage to the fender, core support and quarter panel, it was also pushed in maybe an inch at the B pillar. Also needed an engine, gas tanks, rear subframe/suspension refresh, the diff had a little bit of growl... I wish I could have done something with it, but I just don't have the time or the money right now and don't have anywhere to store it long-term. The upside is that I can focus on the e21 now. Before Ben stopped at the shop with a z71 and a crazy idea to shove an e30 shell in the bed, I was working on getting the subframe cleaned up and removed the part where the drivers side motor mount was. The m42 motor mounts are farther back, so I have to weld new pads onto the subframe where they come down. Also dropped the suspension and started cleaning, cleaning, cleaning.... Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 15, 2015 Author Report Share Posted March 15, 2015 I pulled a sting to see how straight the driveline was going to be. It's attached to the diff flange in the rear, and I used the height of the output flange of the transmission to set the height of the string at the front of the car.I put a pipe across the frame rails so that I'd have something to measure off of after I put the engine and trans in.Whoa... that's not good. The front of the engine about an inch and a half low. Not a huge angle, but enough that I think I'm going to make a new transmission crossmember to compensate.After I was happy with everything I welded up the crossmember and bolted it up to my mock-up engine. It's been a long time since I did any welding, but it turned out pretty good.I was going to work on mounting the center support bearing today, but I forgot to order the the little dust shield that goes on the driveshaft, so I put some candy-colored bushings in my LCAs instead.Making progress, and it feels good. DrLeadFoot and jc43089 2 Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 21, 2015 Author Report Share Posted March 21, 2015 Had to take a picture of this, because... you know... cutting an oil-pan with a hacksaw. It felt wrong, and yet awesome at the same time. Just making a little room for the steering rack. Quote Link to comment Share on other sites More sharing options...
B C Posted March 22, 2015 Report Share Posted March 22, 2015 The cut is finished nicely, works for me. When do you think it will be driving? Quote Link to comment Share on other sites More sharing options...
HipMF Posted March 22, 2015 Author Report Share Posted March 22, 2015 Ah... hard to say. Still have some work to do in the bay before I can paint it. The block is still at the machine shop waiting for pistons. Hopefully they will come this week. Then reassemble the engine, put it in the car, wiring, exhaust, fuel pump and lines, 10 other things that I forgot about and will probably have to wait on parts for.... hopefully early May? Late May is probably more realistic though. Quote Link to comment Share on other sites More sharing options...
suspenceful Posted April 15, 2015 Report Share Posted April 15, 2015 This thing is rad as phuck. Mike's swap by Jake Spence Photography, on Flickr Quote Link to comment Share on other sites More sharing options...
HipMF Posted April 20, 2015 Author Report Share Posted April 20, 2015 Nice! I've been in a bit of a lull lately. Took me a few tries to get the center support bearing mounts for the e30 driveshaft done right. I finally got my pistons and dropped them off at the machine shop. Hopefully I'll have the block back by next weekend. It's been a long time since I made any visible progress, so I decided to put the front suspension back together and put the car back on the ground. I wheeled it outside and rinsed a couple months worth of accumulated dust off of it and now I'm totally stoked about getting it back on the road again. Spent a few hours today scrubbing down the engine bay. Will probably put some paint on it this week. This is what I like to see. A small forest of unused jackstands! suspenceful, DrLeadFoot and KaiserRolls 3 Quote Link to comment Share on other sites More sharing options...
HipMF Posted April 25, 2015 Author Report Share Posted April 25, 2015 B C 1 Quote Link to comment Share on other sites More sharing options...
YoungCR Posted April 25, 2015 Report Share Posted April 25, 2015 Wasn't expecting that! I like it, leftover paint from Ben? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.