GunMetalGrey Posted January 26, 2017 Author Report Share Posted January 26, 2017 Hoses were soft last night. Car is sitting outside in a timeout. Quote Link to comment Share on other sites More sharing options...
straight6pwr Posted January 26, 2017 Report Share Posted January 26, 2017 couple ideas to try - fill the radiator directly from the top hose opening did you run the whole thing with the thermostat completely removed? Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 26, 2017 Author Report Share Posted January 26, 2017 52 minutes ago, straight6pwr said: couple ideas to try - fill the radiator directly from the top hose opening did you run the whole thing with the thermostat completely removed? Yeah, it crept over 1/2 when idling. Quote Link to comment Share on other sites More sharing options...
Boris3 Posted January 26, 2017 Report Share Posted January 26, 2017 Probably missed reading this in earlier posts but is the radiator used or new? If only the top hose and top part of the radiator are getting hot could be a partial blockage issue in the radiator even if fluid is running through it. Flush might dislodge it but not necessarily. As far as blockage somewhere else, block drain plug pulled and block flushed? Getting any heat, if not maybe the blockage is in the heater core? Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 26, 2017 Author Report Share Posted January 26, 2017 I have tried two different radiators, one from the previous car that was known working. Same issue was present in both. Drain plug in block I'm not 100% if I did or not. Heat in cabin is hot as crap when it starts overheating, so that isn't plugged. Quote Link to comment Share on other sites More sharing options...
Boris3 Posted January 26, 2017 Report Share Posted January 26, 2017 Sounds like there is some circulation taking place. Does the bottom radiator hose heat up at all? Thermostat housing is all clean, no partial blocking? I'd go back to KaiserRolls point about shooting with an infrared to get a sense of actual temps at the block, temp sensor housing, etc. You replaced the sensor and checked the plug wiring but how about the gauge (ground nut loose)? Still may be overheating but is the gauge reading the extent accurately? You mentioned water pump blades and freezing earlier, when you stethoscope around the pump area any strange noises? Quote Link to comment Share on other sites More sharing options...
jc43089 Posted January 26, 2017 Report Share Posted January 26, 2017 I would remove and inspect the water pump, if the radiator flows and it will also overheat with no tstat installed, then there is not enough flow going around. Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 27, 2017 Author Report Share Posted January 27, 2017 Water pump was removed and inspected, and appeared to be fully intact. Only time I got lower rad hose temp was with the thermostat removed. All housings appeared to be free of blockages. Water pump to thermostat hose gets crazy hot, upper rad hose gets pretty darn warm, lower hose doesn't do much of anything. I added an additional hole to the upper portion of the thermostat and that didn't appear to help. Thermostat was bench tested / replaced to no avail. My only real lead lately is how hard the hoses got when at operating temp. They were darn near solid, but after the car sat overnight they went back to normal. I can tell it is overheating quite a bit because when it gets up in the temp gauge range it blows insanely hot heat from the vents. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted January 27, 2017 Report Share Posted January 27, 2017 Get a temp gun dude Quote Link to comment Share on other sites More sharing options...
patsbimmer1 Posted January 27, 2017 Report Share Posted January 27, 2017 The upper radiator hose getting hard isn't really relevant. The cooling system is a pressurized system so the upper hose should get hard. The only symptom you have is the lower hose doesn't get hot but with the thermostat removed it does get hot. So your thermostat isn't opening. That's the problem you need to be solving. Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 27, 2017 Author Report Share Posted January 27, 2017 16 minutes ago, patsbimmer1 said: The upper radiator hose getting hard isn't really relevant. The cooling system is a pressurized system so the upper hose should get hard. The only symptom you have is the lower hose doesn't get hot but with the thermostat removed it does get hot. So your thermostat isn't opening. That's the problem you need to be solving. All hoses are rock hard. Not just the upper. I'm aware the thermostat isn't opening, but I have come across no reason for it not to be. This is my problem. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted January 27, 2017 Report Share Posted January 27, 2017 Take the t stat out and toss it in some boiling water and see if it will open Quote Link to comment Share on other sites More sharing options...
Boris3 Posted January 27, 2017 Report Share Posted January 27, 2017 Did you try boiling the thermostats (stove test) to see if they open? Not unheard of to get new ones that are bad out of the box. Quote Link to comment Share on other sites More sharing options...
patsbimmer1 Posted January 27, 2017 Report Share Posted January 27, 2017 I'm just trying to say, don't over think it. It's probably something very obvious causing it. Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 27, 2017 Author Report Share Posted January 27, 2017 I've boiled all thermostats and they opened just fine. Newest one I added an additional hole to assist bleeding. Trying not to overthink it, but I've done all of the simple stuff 3 times now and I'm getting nowhere. I'm running out of ideas. My only other thought is to try switching the heater core hoses, but since the heater works very well I don't think that is it. Though it's probably the last thing I haven't tried. Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 27, 2017 Author Report Share Posted January 27, 2017 Reference for later Quote Link to comment Share on other sites More sharing options...
Boris3 Posted January 27, 2017 Report Share Posted January 27, 2017 To rule out another simple thing, temp gun just to make sure the gauge reading of overheating is in fact correct. Gun is cheap, under $20 at HF. You're still using the stock temp gauge? That was my issue when I was chasing an overheating problem on the m42. Pulled the cluster and tightened the nut on the back of the gauge. No more "overheating". If you tap the temp gauge when it reads high does it jump/move? Another symptom of the loose nut. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted January 27, 2017 Report Share Posted January 27, 2017 Get a temp gun dude Quote Link to comment Share on other sites More sharing options...
Jdesign Posted January 30, 2017 Report Share Posted January 30, 2017 I would get a temp gun or an aftermarket temp gauge and see what your readings are. I am also going to back up Boris mentioning checking the OEM gauge. Also, not to say you are an idiot, as I have done the same thing before, but are you sure the T-stat is facing the right direction? Quote Link to comment Share on other sites More sharing options...
straight6pwr Posted January 30, 2017 Report Share Posted January 30, 2017 guys, he tried without the t-stat and had the same problem. its not the t-stat. Quote Link to comment Share on other sites More sharing options...
GunMetalGrey Posted January 30, 2017 Author Report Share Posted January 30, 2017 3 minutes ago, straight6pwr said: guys, he tried without the t-stat and had the same problem. its not the t-stat. I've kept my cool (pun intended) but mentally am getting annoyed at that question. Thank you for being the one to point it out lol. Car is back in from its time out, and will be looked at tonight. Yes, I do have the thermostat in the correct orientation. Quote Link to comment Share on other sites More sharing options...
KaiserRolls Posted January 30, 2017 Report Share Posted January 30, 2017 Hey Ben. Do you have a temp gun ? Quote Link to comment Share on other sites More sharing options...
straight6pwr Posted January 30, 2017 Report Share Posted January 30, 2017 2 hours ago, GunMetalGrey said: I've kept my cool (pun intended) but mentally am getting annoyed at that question. Thank you for being the one to point it out lol. i think you need a post along the lines of Quote Link to comment Share on other sites More sharing options...
HipMF Posted January 31, 2017 Report Share Posted January 31, 2017 and then when it turns out it's actually in backwards... B C and Jdesign 2 Quote Link to comment Share on other sites More sharing options...
Jdesign Posted January 31, 2017 Report Share Posted January 31, 2017 23 hours ago, GunMetalGrey said: Car is back in from its time out, and will be looked at tonight. So did you look at it? I am sorry for bringing out the T-stat again. I am back to voting for a blocked coolant passage somewheres. GunMetalGrey 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.