Chadley
-
Posts
464 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by Chadley
-
-
UPDATE!!!!!!!!!!!!!!!!!
Chris and Zach have seen this goodness....
Here we go, old motor getting ready to pull
And its out!
See gentlemen, you have to get the ladies help. They clean grease very well
These three bolts on the diff need countersinking. Otherwise they will rub against the oil pan
Base plate for the motor mounts. Bolt and weld
Yummy weld
Got some clean engine bay, and some flat black
Sliding that sucker in. She was a tight fight no doubt. The oil pan was very close to the diff, it took the just right amount of angle, swearing, and prying to get it in
-
Have we thought it could be the VANOS....
? -
it must be why. brains everywhere, just like this forum, we have two brains! two!!
Hah. I think we have a collective total of 1.36 brains on this forum
-
-
Dustin, i'ma shoot ya a call here real soon
UPDATE!!!!
Heres from where I left off last time... I pounded the aluminum case over the dowel pin, so it will stay in place regardless of the plate.
Some red loctite, and...
Something interesting. Either Chrysler was too lazy to paint the timing cover off the motor, or someone replaced it and didnt do a good job painting it. You can see the tan industrial color you find on motors out of buses or drill rigs.
regardless, cover painted and installed
Turbo oil fitting installed. Got it clocked, re-welded the nessacary parts, and it is installed now.
And before you know it....
Phase 1 of 3 is complete Friday I get the transmission, and the 6.5/4L80E comes out. Cummins should be on its way in come saturday
-
^LMAO
-
Cummins=CAT motors, and they're more reliable then the chevy motor.
Best parts from each american diesel truck:
Ford=body
Chevy= Drivetrain/axles etc
Dodge= Motor
No.
Cummins is its own company, has nothing to do with cat or chrysler. Cummins has a deal with dodge to exclusively use cummins in RAM (not with ford or Chevy). Kind of like how Allison has a contract with GM to only use their transmissions in the light duty market.
Cummins has been around for around 80 years. One of the best diesels on the market. Easiest to maintain and modify too, not o mention cheapest to modify.
Also, ford bodies are shit. They rot worse than Chevys.
Ford is good for their axles. That's it. And that's only cause they use DANA axles.
Dodge is only good for the Cummins that comes in it. Pretty much garbage everywhere else.
Chevy has the nicest interior by far. Best driving truck in my opinion. But, they rot too, and have quirks because of their IFS that dodge and ford don't use.
By the way, CUMMINS IS NOT OWNED BY DODGE OR CAT
- KaiserRolls and Rowleym
- 2
-
Want to buy my great condition hx40?
Lol. You funny, the HE is a better flowing turbo.
Unless its for the right price...
AccordinG to my UPS app, my rear housing will be here today!! Also, expect another picture filled update tonignt or tomorrow
-
You've a fender roller TJ?
-
After the turbo road block, I decided to keep the production moving by doing the KDP fix. KDP is the Killer Dowel Pin, and what happens is the small dowel pin placed in the timing case by the factory has a tendancy to work its way out of its spot, and into the gears. It will kill the motor if it does this.
Start with removing the timing cover...
Whats a timing chain again?
This is the dowel pin that walks out. Mine was still there, and relatvely not moved. Fter 221k miles, thats a surprise
This is part one of the solution. the bolt goes through the hole and this plate acts as a blocker to keep the pin from moving.
Part two of the fix is yet to come. At this point in the night I was too drunk to continue what I was doing, so I went inside
-
Went ahead and mocked up my common rail manifold. Was gonna use this to run a set of compound HE351 and Borg Warner S4xx turbos.
But as you can see....
Back to the 2nd gen manifold.
Drilled the manifold so all 6 cylinders are equally gated. On stock manifolds, only the first 3 cylinders are wastegated, leaving for unequal pressure. Drilling a 1/4" hole solves this problem.
Comparison from the HX35 to the HE351. THe 351 is off an 06 Cummins, and was designed to supply air to a 325hp motor. Should be a significant increase from the baby HX thats on the truck now.
Got that sucker mocked up
Notice how the outlet is towards the top? It has been said that will not work, though I think otherwise. At any rate, I took off the T-band clamp to work on a solution. The only real dillema I'm having is the wastegate, I'm not sure if I should just let the turbo float or put a wastegate on the intake tract. I also need to come up with the oil drain, as the HE was designed to work on the common rail manifold, and therefore the oil drain is off for the 12v manifold.
-
Doin work...
Took us 6 hours to pull the motor and trans, including union breaks and eating.
Seperated the transmission, and had it sent to be rebuilt. It is going to be built to bolt up the BW 4401 32 spline GM transfer case, by replacing the main shaft and rear housing. The input shaft will stay dodge, so it will bolt to the 12" cummins clutch. Would love to throw a 13" dual disk setup, but they're 1100 dollars, and I dont have the money for that right now.
This is what was found on the stock clutch... No idea if its original or not
Degreased and painted one side
For the top and other side...
-
Alright. Hurr we go.
Starting with a 93 K3500 Chevy Silverado, DRW of course. Has the legendary (but for the wrong reasons) 6.5 Turbo diesel, with an automatic 4L80E automatic OD transmission.
It ran great for awhile, then I did WMO for 8k miles. Then winter came, and the injectors started to puke. At the same time, the transmission started acting up. I'd lose overdrive every once in awhile, and the truck would surge while driving. Not to mention my mileage was terrible, barley making 11mpg (I reguarlily got 15 when I bought the truck).
Having thought about a 12v swap for awhile, I decided fuck it, nows the time. So I went on the hunt, and before I knew it I found a 95 Dodge Ram 12v with a 5 speed. Perfect!
Bought it in november, but havent done anything until now. Weather and wallet agreed to make this happen.
-
In. 20th is perfect, shouldnt have anything going on
-
-
What hardware/software do you use?
-
will be there
-
I like photography cept I suck LOL
I shoot with a nikon D50. I'll put some pics up whenever I return... muhahahah
-
Reserved for when I have pictures of my garage, when its not littered with parts and other junk
I will tease: powdercoating, blasting cabinet, parts depot, and fuel making happens in the same garage
-
Ride with us then piku!
-
-
Different Ryan, Brian. But Snugglecakes is welcome to share a seat with me...
Chris, since this is all being cooked yet, the drive can vary yet. I was thinking we shoot through one way, and then tour the country slightly the other. I mean, we're going through the country, may as well make some good stops along the way.
Its a 29 hour ride one way from my haus.
-
Poor kitteh... Sorry bud. Never had a cat, but I have a dog, so I understand the feeling.
How old was he?
-
http://www.wibimmers.com/board/search.php?searchid=49374
EVERYONE READ RIGHT MEOW
Anyone wanna see a Chummins in the making?
in General Off-Topic
Posted
Started the day getting the cab ready for the 5 speed. Cut the hole in the carpet, and started grinding away
With the bellhousing bolted to the motor, the transmission had to go in seperately. Seemed easy, the tranny to bellhousing connection only has 4 bolts. Wasnt even close to easy, as it turns out muscling a 300lb transmission into a 1 1/4" hole is harder than it seems. We had to cut this slit to get the shifter into the cab, no big deal.
Forget to take pics of the rest, oh well. Next conundrum, we noticed the motor was slightly offset. This is why
Fixed with...
And I once again forgot to take a picture of the finished product
However...
5 speed is in. Have to get a new spring for my clutch pedal assembly, then I can finish my linkage. With that, the slave will be hooked up. Gotta reuse the Chrysler slave rod with the GM cylinder. Or just the dodge slave. Who knows.
Gentlemen, I present...
CHUMMINS!!!!